AMD铁絮体改性生物炭对重金属吸附机理研究 ——以Pb(II)为例

以酸性矿山废水生成的铁絮体和秸秆生物炭为原料,采用化学改性和紫外辐射联用技术制备改性生物炭,并通过正交试验确定最佳改性条件,同时利用FTIR、SEM和BET等方法对吸附材料的形貌特征、孔隙结构及其表面化学性质进行表征.结果表明,通过改性使吸附材料比表面积增大,吸附位点增多,在25℃、pH为7时,吸附材料改性后比表面积为295.71 m²·g^-1,对Pb（II）的拟合吸附量可达278 mg·g^-1.改性材料对Pb（II）的吸附过程符合Langmuir吸附等温线模型和准二级动力学模型,主要为单分子层吸附,受化学吸附控制.     

滆湖水华初期浮游植物群落特征及与水环境因子相关性分析

为探究滆湖水华初期浮游植物群落特征及与水环境因子的相关性,于2018年5—7月在全湖布设22个点,调查研究滆湖水华初期浮游植物群落时空分布特征,并对引起水华主导环境因子进行分析.结果表明：①共获得7门119属,优势属为绿藻门的小球藻与球团藻、蓝藻门的鞘丝藻与微囊藻,其中湖心区域浮游植物丰度与多样性小,均匀性低,属于中偏重污染区域;湖北区以北属于中污染区域,蓝藻堆积严重;西部沿岸及南端区域属于中偏轻污染区域.②冗余分析得出,湖心藻类与水温（T）有强相关性,与叶绿素a（Chl-a）、溶解性总磷（DTP）、pH、溶解氧（DO）呈一定正相关性;湖北区以北藻类与底泥有机质（OM）、水体悬浮物（SS）、Chl-a及DTP呈强相关性,与T呈一定相关性.T与多项环境因子相关,均值从26.1℃上升到32.4℃;OM与有机磷（OP）呈高度相关性（p<0.05,r=0.892）.水华发生的主导环境因子为T、DTP与pH,底泥OM及OP有一定影响.     

南京市饮用水源地抗生素污染特征及风险评估

采用固相萃取-液相色谱-串联质谱技术（SPE-HPLC-MS/MS）,对南京市饮用水源地抗生素含量及分布特征进行了分析.结果表明,17个采样点总浓度为0.56~1994.96 ng·L^-1,共检出5种大环内酯类、13种磺胺类、3种四环素类、8种喹诺酮类抗生素,平均浓度为0.30~37.07 ng·L^-1,其中检出浓度最高的抗生素为环丙沙星（CIP）,浓度为317.60 ng·L^-1,检出率最高的抗生素为克林霉素（CLI）,检出率为88.24%.与国内部分河流相比,南京市饮用水源地水体中大环内酯类、四环素类、喹诺酮类抗生素残留浓度处于较高水平.生态风险评估结果表明,点位S7具有最高的联合风险熵值（24.58）,氧氟沙星（OFX）的风险熵值最高,达到13.06;健康风险评估结果表明,9种抗生素对人体健康的风险熵Q_H为1.70×10^-3~9.47,强力霉素（DOX）、诺氟沙星（NOR）、恩诺沙星（ERX）、CIP和OFX对大部分年龄段的人体健康具有高水平风险.     

滇黔桂岩溶区河漫滩土壤重金属含量、来源及潜在生态风险

利用全国地球化学基准计划在滇黔桂岩溶区35个点位采集的70件河漫滩表、深层土壤样品,分析了As、Cd、Cr、Cu、Hg、Ni、Pb和Zn 8种重金属元素含量特征,探究了重金属来源、污染状况及潜在生态风险.结果表明,8种重金属元素含量大部分均高于全国土壤背景值,在滇东南地区含量最高,桂西北地区最低.表层土壤Cd、Hg明显富集,As、Cr、Cu、Ni与深层土壤含量相当;As、Cd、Hg、Pb、Zn在农田、菜地中明显高于深层土壤,Cr、Cu和Ni在各类土地中与深层土壤相当.因子分析结果显示,表层土壤中Cd、Cr、Cu、Ni受地质背景控制,As、Pb、Zn既与地质背景有关,也受人为活动影响,Hg受人为活动影响较严重;深层土壤中Cd、Cr、Cu、Ni、Cr、Zn继承了区域母岩特征,As、Hg和Pb受地质背景和人为活动双重影响.地累积指数法和富集因子法污染评价结果表明,研究区河漫滩表层土壤中Cd、Hg污染较重,As、Cr、Cu、Ni、Pb、Zn大部分为轻度污染或无污染.各重金属潜在生态风险指数高低顺序依次为Hg > Cd > As > Cu > Ni > Pb > Cr > Zn,Cd和Hg的生态风险指数之和占综合指数的82.43%,生态风险最高;滇东南地区重金属潜在风险综合指数最高,具重度生态风险.     

酸性紫色水稻土颗粒有机质对镉的吸附特性

采集典型的酸性紫色水稻土（APPS）,从中分离出颗粒有机质（POM）,通过批量试验研究POM及其来源土壤Cd²⁺的吸附动力学、等温吸附和热力学特征,通过扫描电镜-能谱仪、傅里叶红外光谱仪等手段及吸附前后镉的形态变化的测定,研究了POM对Cd²⁺的吸附机制.结果表明：POM对Cd²⁺的亲和力远高于其来源土壤.POM及土壤对Cd²⁺的吸附动力学最优模型均为准二级动力学.Langmuir、Freundlich方程均能较好地描述其等温吸附特征,其中对POM,以Freundlich方程更优,表明POM对Cd²⁺的吸附属于多分子层的非均质吸附.吸附热力学参数△G^θ均小于0、△H^θ和△S^θ均大于0,表明吸附属于自发吸热过程.根据△H^θ值及解吸试验判定POM对Cd²⁺的吸附以化学吸附为主,土壤对Cd²⁺的吸附过程以物理吸附为主.吸附平衡后,土壤中可交换态镉比例提高,而POM中交换态和络合态镉比例增加.综上及吸附前后POM的表征结果说明,POM对Cd²⁺的吸附机制包括含氧官能团的络合、离子交换、阳离子-π键、沉淀作用和静电吸附.     

2018年春节期间京津冀地区污染过程分析

为了解2018年春节期间京津冀地区空气污染情况,利用近地面污染物浓度数据、激光雷达组网观测数据,结合WRF气象要素、颗粒物输送通量和HYSPLIT气团轨迹综合分析污染过程.结果表明,春节期间出现3次污染过程.春节前一次污染过程,各站点PM_2.5浓度均未超过200μg/m³;除夕夜,廊坊站点PM_2.5峰值浓度达到504μg/m³,是清洁天气的26倍;年初二~初五,各站点PM_2.5始终高于120μg/m³,且污染主要聚集在500m高度以下,北京地区存在高空传输,800m处最大输送通量达939μg/（m³·s）,此次重污染过程为一次典型的区域累积和传输过程.京津冀地区处于严格管控状态时,燃放烟花爆竹期间PM_2.5峰值浓度可达无燃放时PM_2.5峰值的3.2倍.为防止春节期间重污染现象的发生,需对静稳天气下燃放烟花炮竹采取预防对策.     

Density functional theory (DFT) studies of vanadium-titanium based selective catalytic reduction (SCR) catalysts

Based on density functional theory (DFT) and basic structure models, the chemical reactions on the surface of vanadium-titanium based selective catalytic reduction (SCR) denitrification catalysts were summarized. Reasonable structural models (non-periodic and periodic structural models) are the basis of density functional calculations. A periodic structure model was more appropriate to represent the catalyst surface, and its theoretical calculation results were more comparable with the experimental results than a non-periodic model. It is generally believed that the SCR mechanism where NH₃ and NO react to produce N₂ and H₂O follows an Eley-Rideal type mechanism. NH₂NO was found to be an important intermediate in the SCR reaction, with multiple production routes. Simultaneously, the effects of H₂O, SO₂ and metal on SCR catalysts were also summarized.     

Preparation of solar-enhanced AlZnO@carbon nano-substrates for remediation of textile wastewaters

Photoactive aluminum doped ZnO(AlZnO) was synthesized by sol-gel method.After that,AlZnO photocatalyst was deposited on five carbon-based materials(CBMs) using ultrasonic route followed by solid-state mixing using ball mill.The CBMs used were poly aniline(PANI),carbon nitride(CN),carbon nanotubes(CNT),graphene(G),and carbon nanofibers(CNF).The crystal phases,elemental compositions,morphological,and optical properties of the AlZnO@CBMs composites were investigated.Experimental results revealed that two of AlZnO@CBMs composites exhibited superior bleaching efficiency(100% removal) and photocatalytic stability(three cycles) for 50 μmol/L Methylene Blue(MB) contaminated water after 60 min irradiation in visible light at pH 6.5,0.7% H_2O_2,and 5 g/L inorganic salts.Under optimum conditions,AlZnO@CBMs nanocomposites were employed for the treatment of mixed dyestuffs composed of MB,Methyl Orange(MO),Astrazone Blue FRR(BB 69),and Rhodamine B(RhB) dyes under dark,ultraviolet,visible,and direct sunlight.For mixed dyestuffs,the AlZnO@G achieved the highest dye sorption capacity(60.91 μmol dye stuffs/g) with kinetic rate 8.22 × 10~(-3) min~(-1) in 90 min via multi-layer physisorption(Freundlich isotherm) on graphene sheet.In additions,AlZnO@CN offered the highest photo-kinetic rate(K_(photo)) of～54.1 × 10~(-3) min~(-1)(93.8% after 60 min) under direct sunlight.Furthermore,the selective radical trapping experiment confirmed that the holes and oxidative superoxide radicals are crucial on dyes photodegradation pathway.Owing to their superior performance,AlZnO@G and AlZnO@CN nanocomposites can offer an effective in-situ solar-assisted adsorption/photocatalytic remediation of textile wastewater effluents.     

Recent advances in catalytic decomposition of ozone

Ozone (O₃), as a harmful air pollutant, has been of wide concern. Safe, efficient, and economical O₃ removal methods urgently need to be developed. Catalytic decomposition is the most promising method for O₃ removal, especially at room temperature or even subzero temperatures. Great efforts have been made to develop high-efficiency catalysts for O₃ decomposition that can operate at low temperatures, high space velocity and high humidity. First, this review describes the general reaction mechanism of O₃ decomposition on noble metal and transition metal oxide catalysts. Then, progress on the O₃ decomposition performance of various catalysts in the past 30 years is summarized in detail. The main focus is the O₃ decomposition performance of manganese oxides, which are divided into supported manganese oxides and non-supported manganese oxides. Methods to improve the activity, stability, and humidity resistance of manganese oxide catalysts for O₃ decomposition are also summarized. The deactivation mechanisms of manganese oxides under dry and humid conditions are discussed. The O₃ decomposition performance of monolithic catalysts is also summarized from the perspective of industrial applications. Finally, the future development directions and prospects of O₃ catalytic decomposition technology are put forward.     

基于边介数的省域生态廊道构建方法优化

我国城市建设和生态保护工作均对土地资源有大量需求,二者之间的矛盾在经济优先发展区表现尤为明显.为了有效地改善生态环境,管控土地利用并引导其变化发展,需要建设具备不可替代特征的省域生态廊道.最小累积阻力模型（minimum cumulative resistance,MCR）是识别生态廊道最常用、有效的模型,但在应用于省域尺度时,MCR模型识别的潜在廊道路由存在冗余的问题.因此,通过引入网络科学中的边介数指数（edge-betweenness）对MCR模型进行优化,计算潜在廊道路由的边介数指数值,选取出其中最为重要和简明的结构来连通生态源地,即提取潜在路由中的骨干路由（backbone route）和关键战略点（key strategic point）作为不可替代的结构来指导省域生态廊道建设.将优化后的MCR模型应用于广东省,构建了全长5 493 km的省域生态廊道,其中包含生态源地20处,关键战略点11个,骨干生态廊道29条.骨干路由与关键战略点构成的不可替代省域生态廊道（irreplaceable provincial corridor）能够实现"廊道数量和占地面积最少、连通性基本不变"的目标.研究显示,边介数能够对潜在路由进行优化筛选,识别出维护省域生态安全的关键结构;不可替代生态廊道能够指导省域生态规划和土地空间的发展利用,并为更高水平的生态安全环境提供了演进的基础;同时也为土地资源紧张的地区提供了建设生态廊道的参考与依据.